2021-09-22 Stamping Guide Comments Off on Introduction to the processing points of aluminum stamping parts
1. stamping die design. The raw material of aluminum stamping parts, aluminum, is relatively soft. When stamping parts are used for stamping, it is easy to cause material blocking. Therefore, when des...
2021-09-22 Stamping Guide Comments Off on What are the requirements for precision hardware
Precision metal stamping parts are stamped from non-ferrous metals and other materials into the required shape and size by external force, and then cut and separated. The materials, stamping dies and ...
2021-09-22 Stamping Guide Comments Off on The layout principle of process incision
The size and shape of the process incision depends on the area in which it is located and the requirements for external supplementary materials. Generally, the following principles should be followed:...
2021-09-22 Stamping Guide Comments Off on Introduction of metal drawing process
(1) According to the drawing of the workpiece, analyze the shape characteristics, size, precision requirements, raw material size and mechanical properties of the workpiece, and combine factors such a...
2021-09-22 Stamping Guide Comments Off on Stretching oil selection
(1) Since silicon steel plate is a material that is relatively easy to stretch, low-viscosity stamping oil will be used on the premise of preventing scratches for the easy cleaning of the finished wor...
2021-09-22 Stamping Guide Comments Off on What are the advantages of stamping parts
(1) stamping parts manufacturers have high production efficiency in stamping processing, and they are easy to operate and easy to realize mechanization and automation. This is because stamping relies ...
2021-09-22 Stamping Guide Comments Off on What are the forms of mold failure
(1) Wear and failure of the stamping die manufacturer: When the die is in service, it contacts the forming blank and produces relative movement. The phenomenon that the contact surface gradually loses...
2021-09-21 Stamping Guide Comments Off on The main points of the design of the metal mold cavity
The main point of the design of the metal mold cavity is to avoid the blanking waste from accumulating in the cavity of the cavity. The problem with the main point lies in the large blanking force req...
2021-09-21 Stamping Guide Comments Off on What are the characteristics of stamping operations
1. High production efficiency The number of parts or process content completed per unit time is several times higher than that of general cnc machining methods, or even hundreds to thousands of times....
2021-09-21 Stamping Guide Comments Off on The mechanism of material deformation of metal stamping parts
The stretching and plastic deformation process of metal stamping parts is mainly composed of three stages: uniform elongation stage, partial elongation stage, and cracking stage. The uniform elongatio...
2021-09-21 Stamping Guide Comments Off on Advantages of precision metal stamping
1. Simple operation, convenient for mass production, and easy to realize mechanization and automation. 2. The precision metal stamping processing function is relatively stable, and the stamping parts ...
2021-09-21 Stamping Guide Comments Off on Introduction to stamping design standard knowledge
1. When designing metal stamping parts, it should be ensured that under normal use, the dimensional accuracy and surface roughness requirements should be as low as possible, and it should be beneficia...
2021-09-21 Stamping Guide Comments Off on What are the common undesirable phenomena of coil materials?
1. There is foreign matter on the surface or inside of the steel plate; 2. The foreign body is peeling off, and the coil is in the same state as a scar; the coil is bad 3. The corners of the coil are ...
2021-09-21 Stamping Guide Comments Off on Introduction to stamping parts processing knowledge
1. In the daily mold production of metal stamping parts processing, attention should be paid to maintaining the sharpness of the punching convex and concave die cutting edges. When the punching edge i...
2021-09-17 Stamping Guide Comments Off on Some Opinions on the Design and Production Maintenance of Precision High Speed Stamping Die
Some Opinions on the Design and Production Maintenance of Precision High Speed stamping Die High-speed stamping production technology is highly developed in the market economy due to its high effici...
2021-09-16 Stamping Guide Comments Off on Primary processes involved in metal stamping parts
Complex parts often require a series of several different steps to create. Parts that may seem simple at first glance rarely need only one stamping step to be considered properly completed. Confusion ...
2021-09-16 Stamping Guide Comments Off on Deep Drawing Advantages and Disadvantages
Metal forming using deep drawing has its advantages and disadvantages. In general, the deep drawing method is highly valuable for large quantity or long run production orders for multiple reasons. Tha...
2021-09-16 Stamping Guide Comments Off on Budgetary quote of sheet metal stamping parts from US
In February 2019, we got one quote of sheet metal part from United States. Below is the details: I need a quote for sheet metal stamping parts deliver to Texas United States. Please quote part a...
2021-09-15 Stamping Guide Comments Off on Why you need to choose metal stamping company?
The metal stamping is a process of punching, making three dimensional shapes or size or designs in the metal. Precision metal stamping machines produce a high intensity of energy to engrave dies and f...
2021-09-15 Stamping Guide Comments Off on Top 10 sheet metal stamping companies you must know
Are you looking for professional sheet metal stamping companies for high quality metal stamping parts? Here you must know top 10 sheet metal stamping companies. 1. Acro Metal Stamping: A Precision Met...
